Three types warehouse floor, which is better!
Judging from the current floor laying situation, many logistics storage centers still use ordinary concrete floors. This type of floor is economical but also a headache “problem household”. Under the frequent operation of forklifts, it is different. Problems such as sand founding and dusting to a certain degree still occur from time to time, and the longer the age, the more serious the problem. In addition to weathering, water erosion, carbonization and other problems, floor powder will become the problem of many cement concrete floors with a long service life. normal.
Whether the warehouse floor design is reasonable or not directly means whether the construction effect can match the needs of the warehouse, and it has a significant impact on the storage and transportation costs and energy efficiency of the goods in the warehouse. Therefore, if we want to improve the operational efficiency of the warehouse scientifically and reasonably, we need to pay attention to the decoration of the warehouse floor.
The following editor mainly introduces three common floors for warehouse decoration at present. As for which floor is good for warehouse floors, we will know after a comparison.
Wear-resistant aggregate floor
Process introduction:
Wear-resistant aggregate floor materials include different selected (quartz sand, emery, metal, alloy) aggregates, special cement, polymer additives, pigments, etc., uniformly mixed together. Typical floor types include terrazzo floor, Emery floor and so on. The wear-resistant floor is mainly to spray wear-resistant floor materials evenly on the surface of the newly poured cement concrete, and then use a trowel to lift the slurry and light up, use the base concrete slurry to wet the wear-resistant material and form a whole with the base concrete , So as to achieve the surface layer’s wear resistance and non-slip, not only improve the surface strength of the floor, but also better avoid dust and sand turning.
Advantages:
high level of hardness, excellent dust resistance, wear resistance, and impact resistance.
Disadvantages:
The construction of wear-resistant aggregate needs to be synchronized with concrete pouring to ensure the effect, and it is generally more suitable for new ground construction. Construction on the old floor requires an additional layer of fine stone concrete of more than 5 cm, which is usually expensive.
Epoxy coated floor
Process introduction:
Epoxy floor mainly relies on epoxy floor paint for painting and construction. It has the characteristics of no joints, solid texture, good chemical resistance, anti-corrosion, dustproof, and convenient maintenance. It is often used in hygiene requirements and dustproof More demanding places.
Advantages:
The epoxy floor has strong barrier ability, can be used as a ground waterproof material, and has good anti-corrosion and dust-proof effects, and is suitable for precision industries such as pharmaceuticals and electronics.
Disadvantages:
The mechanical properties of the epoxy floor are relatively general, it is easy to be scratched by sharp objects, and is greatly affected by the original ground. As the use time goes by, there will be varying degrees of peeling and falling off. At the same time, forklift tire wear will leave deep marks, which are difficult to remove and affect the appearance. It has poor light resistance and is prone to “chalking” and discoloration under ultraviolet light for a long time. Generally speaking, it is not suitable for outdoor use. In addition, the cost is high and the service life is short, so it is generally recommended to be used in sites with specific requirements for dust and corrosion protection.
curing floor
Process introduction:
The curing floor mainly relies on the concrete sealing curing agent to build. After the material penetrates into the ground, it can be completely integrated with the ground. After the chemical reaction occurs, the hardness, wear resistance and compactness of the cement-based ground can be greatly improved. After being treated with a floor grinder, it can form a solid as steel and bright as a mirror effect.
Advantages:
The solidified floor can be practical, decorative and economical, simple, economical and easy to operate. It is one of the most popular floor crafts at present; it has strong compatibility and is suitable for most cement-based floors. Both the ground and the old ground can be applied, so the scope of application is quite wide. Ideal laying locations include industrial plants, underground parking lots, warehouses, schools, hospitals, shopping malls, cold storage airports, piers and gymnasiums, but not limited to this. In practical applications, there are wear resistance, durability, increased hardness, and dust resistance. , Impermeability, easy to clean and other requirements of concrete floors can be used.
Disadvantages:
no dyeing process is used, the color of the finished floor is the original color of cement, and the visual effect is relatively simple.
Summary:
In the logistics storage center, the first problem that the floor must solve is how to resist the friction of the forklift truck and the wheels to achieve a beautiful and durable effect. The newly-built logistics storage center is different from the project-renovated logistics storage center. The newly-built logistics storage center can choose a cost-effective and practical wear-resistant floor; in addition to the wear-resistant floor, the reconstructed logistics storage center can be coated with epoxy on the original ground Floor, concrete sealing curing agent floor,